Protein determination in food analysis

One of the most frequently reported values in food analysis

A calculation built on a nitrogen measurement

Protein content is one of the most frequently reported values in food analysis, appearing on nutrition labels, feed specifications, and quality control certificates. Yet no routine laboratory method measures protein directly. Protein determination in food chemistry is, almost without exception, a calculation built on a nitrogen measurement, and understanding that gap is essential for interpreting results correctly.

How is protein content determined?

In practice, food laboratories determine protein content indirectly, by first measuring total nitrogen using either the Kjeldahl or Dumas method, then converting that nitrogen value into a protein value using a conversion factor. This two-step process, nitrogen determination followed by conversion, is the basis for the vast majority of protein values reported on food labels and in regulatory submissions worldwide, and it has remained largely unchanged in principle since Johan Kjeldahl introduced his method in 1883.

Direct protein measurement methods do exist outside routine food testing, biuret, Bradford, and BCA (bicinchoninic acid) assays are all used in biochemistry and research settings to quantify protein via colorimetric reaction with peptide bonds or specific amino acid residues. These methods see limited use in food quality control, however, since they typically require soluble, extracted protein rather than intact food matrices, and are less practical for the diverse, complex samples routine food laboratories handle.

Why is protein calculated from nitrogen?

Nitrogen is used as a proxy for protein because protein is, on average, the dominant nitrogen-containing component in most foods, and nitrogen is comparatively straightforward to measure with high precision using well-established wet chemistry or combustion techniques. Amino acids, the building blocks of protein, average approximately 16 percent nitrogen by weight, which is where the widely used general conversion factor of 6.25 originates, since 100 divided by 16 equals 6.25.

This approach is fast, inexpensive relative to direct amino acid analysis, and backed by more than a century of standardisation across ISO, AOAC, and IDF reference methods. Its central limitation is one of specificity, nitrogen determination captures all nitrogen in a sample, not only the nitrogen bound in protein.

What is crude protein?

Crude protein is the term used for protein content calculated directly from total nitrogen, without correcting for non-protein nitrogen (NPN) sources such as free amino acids, nucleic acids, urea, and ammonia. It is the value produced by standard Kjeldahl and Dumas methods applied to a whole sample, and it is the figure most commonly reported on nutrition labels and feed specifications, precisely because it can be obtained quickly and reproducibly.

The word “crude” is a technical qualifier, not a judgement on quality, it signals that the value is derived from total nitrogen rather than verified protein-specific measurement, and it is the standard terminology used throughout AOAC and ISO methodology.

True protein vs crude protein

True protein refers to protein content after non-protein nitrogen has been excluded from the calculation. It is typically obtained by first precipitating protein out of solution, commonly using trichloroacetic acid (TCA), and then measuring the nitrogen remaining in the non-precipitated fraction as NPN. True protein is then calculated as total Kjeldahl nitrogen minus non-protein nitrogen, multiplied by the appropriate conversion factor.

This distinction is standardised for dairy specifically, AOAC methods 991.21, 991.22, and 991.23 describe TCA-based procedures for separating protein and NPN fractions in milk, refining the crude protein figure obtained by AOAC 991.20 or ISO 8968-1/IDF 20-1. The gap between crude and true protein varies by matrix, in milk, NPN typically accounts for a small but analytically meaningful percentage of total nitrogen, which is one reason dairy has some of the most developed NPN methodology of any food category.

 Crude ProteinTrue Protein
DefinitionProtein content calculated from total nitrogen without correcting for non-protein nitrogen (NPN) compounds.Protein content calculated after excluding non-protein nitrogen (NPN) compounds.
Nitrogen source measuredAll nitrogen in the sample.Only nitrogen associated with true proteins.
Includes NPN compounds?YesNo
Examples of NPN compoundsFree amino acids, nucleic acids, urea, ammonia.Excluded from the calculation.
CalculationTotal nitrogen × protein conversion factor.(Total Kjeldahl nitrogen − NPN nitrogen) × protein conversion factor.
Analytical methodsTypically determined by Kjeldahl or Dumas methods.Determined by measuring total nitrogen and NPN separately, often after TCA precipitation.
Accuracy for actual protein contentMay overestimate protein because NPN contributes to the nitrogen measurement.More accurately reflects the actual protein present.
Common useNutrition labels, feed specifications, routine quality control.Research, dairy analysis, and applications requiring accurate protein quantification.
Regulatory statusMost commonly reported protein value in food and feed analysis.Used when distinguishing protein nitrogen from NPN is important.
Typical valueUsually slightly higher than true protein.Usually slightly lower than crude protein.

Why protein conversion factors differ between food types

Conversion factors differ because the nitrogen content of protein itself varies depending on amino acid composition, different proteins contain different proportions of nitrogen-rich versus nitrogen-poor amino acids, so a single universal factor inevitably introduces error for foods whose proteins deviate from the average composition the 6.25 factor assumes.

Milk protein, for example, uses a factor of 6.38, a value proposed by Hammarsten and Sebelien in 1892 based on purified casein containing approximately 15.67 percent nitrogen, notably lower than the 16 percent average the general factor assumes. Wheat and other cereal proteins use a lower factor, close to 5.70, reflecting their comparatively higher proportion of nitrogen-rich glutamine and proline residues relative to total protein mass. These food-specific values, often referred to as Jones factors, are covered in full with a reference table in our dedicated article on protein conversion factors.

Which protein conversion factor should you use?

The correct factor depends on the specific food matrix and the regulatory or reference method governing the analysis. Where a matrix has an established, standardised factor, milk at 6.38, wheat at approximately 5.70, soy protein commonly at 5.71, that factor should be used and documented, since it is what regulatory bodies and reference methods expect. Where no matrix-specific factor is established or validated, the general factor of 6.25 remains the default.

Laboratories working across diverse product categories, particularly composite or novel foods, should treat conversion factor selection as a documented methodological decision, not an afterthought, since an incorrect factor produces a systematic bias in every reported result, not a random error that averages out with repeated testing.

When nitrogen is not an accurate predictor of protein

Nitrogen becomes an unreliable predictor of protein content in several recurring scenarios. Matrices with naturally high non-protein nitrogen content, such as raw milk, certain fermented products, and some vegetables, will overstate true protein if only crude protein is reported. Novel and alternative protein matrices, including many plant-based and fermentation-derived proteins, frequently lack a validated, matrix-specific conversion factor, meaning the default 6.25 factor may not reflect their actual amino acid composition with any precision. Any sample subject to intentional adulteration with nitrogen-rich, non-protein compounds will produce inflated crude protein values regardless of which nitrogen method is used, since the vulnerability lies in the nitrogen-to-protein assumption itself, not in Kjeldahl or Dumas execution.

In each of these cases, laboratories requiring defensible protein values, rather than a routine crude protein estimate, should consider NPN correction, amino acid based analysis, or matrix-specific conversion factor validation as part of their testing strategy.

Discuss your food analysis requirements

Our Xperts are happy to discuss your application and help you find the right solution.

FAQ

What is protein determination in food analysis?

Protein determination is the process of estimating the protein content of a food product by first measuring its nitrogen content and then applying a protein conversion factor. Most routine food laboratories use nitrogen determination methods such as Kjeldahl or Dumas because direct protein measurement is not practical for many food matrices.

Protein content is typically determined by measuring total nitrogen and multiplying the result by a protein conversion factor. The most widely used methods for nitrogen determination are the Kjeldahl method and the Dumas combustion method.

Protein is calculated from nitrogen because proteins contain nitrogen as a fundamental component of amino acids. Nitrogen can be measured accurately and efficiently, making it a practical proxy for estimating protein content.

The most commonly used protein conversion factor is 6.25. This factor is based on the assumption that proteins contain approximately 16% nitrogen on average.

Crude protein is the protein value calculated directly from total nitrogen without correcting for non-protein nitrogen compounds. It is the most commonly reported protein value on food labels, feed specifications, and quality certificates.

Crude protein includes all measured nitrogen, including non-protein nitrogen sources such as urea, ammonia, and free amino acids. True protein excludes non-protein nitrogen and therefore provides a more accurate representation of actual protein content.

True protein is the protein content remaining after non-protein nitrogen compounds have been removed or corrected for. It is often determined by separating proteins through precipitation techniques before nitrogen measurement.

The two internationally accepted methods for routine protein determination are the Kjeldahl method and the Dumas combustion method. Both measure nitrogen and calculate protein from the nitrogen result.

Protein conversion factors differ because proteins from different food sources contain different amounts of nitrogen. Using food-specific factors improves the accuracy of calculated protein values.

Milk proteins are typically converted using a factor of 6.38 because milk proteins contain slightly less nitrogen than the average protein assumed by the general factor of 6.25.

Wheat proteins are commonly converted using a factor of approximately 5.70, reflecting their amino acid composition and nitrogen content.

Soy protein is often calculated using a conversion factor of approximately 5.71.

Contact our Xperts

Prefer to give us a call?

The Netherlands
+31 (0)294 280 450

Belgium & Luxembourg
+32 (02)2 334 22 70