How do you troubleshoot poor peak separation in a CHNS analyzer?

Poor peak separation in a CHNS analyzer is most commonly caused by a degraded or contaminated GC separation column, an incorrect carrier gas flow rate, or spent reagent tubes that produce interfering combustion byproducts. Addressing these three areas in a logical sequence resolves the majority of separation problems encountered in routine elemental analysis.

Because CHNS analyzers rely on combustion chromatography to detect carbon, hydrogen, nitrogen, and sulfur simultaneously, even small disruptions to the gas flow path or column chemistry can cause peaks to broaden, shift, or merge. The sections below walk through each contributing factor and the diagnostic steps that help restore resolution quickly.

What causes poor peak separation in a CHNS analyzer?

Poor peak separation in a CHNS analyzer occurs when the detector cannot distinguish individual elemental signals cleanly, causing overlapping or broadened peaks on the chromatogram. The root causes fall into three main categories: column degradation, flow rate deviation, and reagent tube exhaustion. Identifying which category applies is the first step in any troubleshooting workflow.

In combustion analyzer chromatography, each element’s combustion product travels through the separation column at a characteristic retention time. When peaks overlap, it means one or more products are eluting too close together or too slowly. This can happen gradually as consumables age, or suddenly after a contaminated sample is run. Moisture ingress, oxygen breakthrough, and sample overload are also frequent triggers that accelerate column and reagent degradation.

How does the GC column condition affect peak resolution?

The GC column in a CHNS analyzer is responsible for separating combustion gases by their physicochemical affinity with the column packing material. When the column becomes contaminated, partially blocked, or loses its stationary phase activity, retention times shift and peaks broaden, reducing resolution between adjacent signals.

Column degradation is often gradual. Early signs include a slow drift in retention times, a slight broadening of the nitrogen or sulfur peak, or a reduction in peak height without a corresponding drop in sample mass. As degradation progresses, peaks that were once baseline-resolved begin to merge.

Practical indicators that the GC column is the source of poor separation include:

  • Retention times that have drifted more than a few seconds from the certified reference values
  • Asymmetric peak shapes, particularly tailing on the trailing edge
  • Loss of resolution that persists after verifying the correct carrier gas flow
  • Visible discoloration or channeling when the column is removed and inspected
  • Inconsistent results across replicates of the same certified reference material

Conditioning a mildly contaminated column by running it at elevated temperature under carrier gas flow can sometimes restore partial activity. However, if resolution does not recover after conditioning, column replacement is the appropriate next step rather than continued recalibration attempts.

What role does carrier gas flow rate play in peak separation?

The carrier gas flow rate directly controls how quickly combustion gases move through the GC column in a CHNS analyzer. If the flow rate is too high, gases elute before the column can fully separate them, causing peaks to crowd together. If the flow rate is too low, peaks broaden excessively and analysis time extends, which can introduce baseline drift.

Each CHNS analyzer model is designed to operate within a defined flow rate range for its separation column. Deviations as small as a few milliliters per minute can measurably reduce peak resolution, particularly for elements with similar retention characteristics. Checking the actual flow rate against the instrument’s target specification should always be an early step in any troubleshooting sequence.

Common flow-related causes of poor separation include a partially blocked flow controller, a leak at a fitting or connection, or a carrier gas supply pressure that has dropped below the required inlet pressure. Verifying gas purity is equally important, since carrier gas contaminated with moisture or oxygen will degrade the column and reagents independently of flow rate.

How do reagent tube conditions contribute to overlapping peaks?

Reagent tubes in a CHNS analyzer perform specific chemical reduction and scrubbing functions after combustion. When these tubes are exhausted or partially spent, they allow interfering compounds to reach the separation column, producing ghost peaks, baseline disturbances, or overlapping signals that mimic poor column resolution.

The reduction tube, typically packed with copper or a similar reducing agent, converts nitrogen oxides to elemental nitrogen and removes excess oxygen. If the copper becomes fully oxidized, nitrogen oxides pass through and co-elute with other analyte peaks. Similarly, a spent halogen scrubber allows chlorine or fluorine compounds from halogenated samples to reach the column, causing severe peak distortion.

Reagent tube exhaustion is often underestimated as a cause of peak separation problems because the effect can appear gradually. Monitoring the number of samples run since the last reagent change, and comparing current chromatograms against a baseline run on a known reference material, helps identify reagent-related degradation before it becomes severe.

What are the step-by-step checks for diagnosing separation problems?

Diagnosing poor peak separation in a CHNS analyzer follows a logical sequence that moves from the simplest and most reversible causes to the more involved interventions. Starting with the easiest checks avoids unnecessary column or reagent replacements.

  1. Verify carrier gas supply and flow rate. Confirm the inlet pressure is within specification and measure the actual flow rate at the instrument. Check all fittings for leaks using an appropriate leak detection method.
  2. Run a certified reference material. Compare the resulting chromatogram against a stored baseline or the instrument’s original calibration chromatogram. Note which peaks are affected and whether retention times have shifted.
  3. Inspect the reagent tube fill levels and color. Visually check whether the reduction tube material shows signs of exhaustion. If the tube is within its expected service interval but the instrument has processed a high number of halogenated or sulfur-rich samples, consider early replacement.
  4. Condition the separation column. Run the column at the manufacturer’s recommended conditioning temperature under carrier gas flow for the specified duration. Re-run the reference material and compare resolution.
  5. Check the combustion tube and liner. Residue buildup at the combustion zone can cause incomplete combustion, generating byproducts that overload the separation system.
  6. Review recent sample types. If separation problems appeared after running an unusual matrix, consider whether that matrix could have introduced contaminants that require targeted remediation.

Systematic documentation of each check and its result makes it significantly easier to identify recurring patterns and anticipate consumable replacement intervals for future runs.

When should you replace the separation column versus recalibrating the method?

Replace the separation column when peak resolution cannot be restored through conditioning, flow rate correction, or reagent replacement. Recalibration is appropriate when peaks are well-resolved but retention time drift or sensitivity loss is causing inaccurate quantification. Recalibrating around a degraded column only masks the underlying problem and will produce unreliable results over time.

A practical way to distinguish the two situations is to run a fresh certified reference material after each corrective action. If peak shapes are clean and symmetrical but the calculated elemental percentages are outside the certified range, recalibration addresses the issue. If peak shapes remain broad, asymmetric, or overlapping regardless of method adjustments, the column itself is the limiting factor and should be replaced.

It is worth noting that recalibration frequency should be driven by instrument performance data and the requirements of the applicable quality system, not by a fixed calendar schedule alone. In regulated environments, any column replacement should be followed by a system suitability check before resuming sample analysis.

How SciSPX supports CHNS analyzer troubleshooting in the Benelux

For laboratories in the Benelux region, SciSPX offers specialized support for elemental analysis instrumentation, including CHNS analyzers. Their team of certified Product Specialists and Service Engineers works directly at the application level, helping labs diagnose persistent separation problems, evaluate consumable replacement cycles, and maintain instrument performance in line with GMP and GLP requirements.

SciSPX’s support model covers:

  • On-site diagnostics and corrective maintenance for CHNS and combustion analyzers
  • IQ/OQ installation and validation services for regulated laboratory environments
  • Application-level guidance on method optimization and carrier gas management
  • Preventive maintenance programs designed to extend column and reagent service life

If your lab is experiencing recurring peak separation issues or wants to establish a structured maintenance program for its elemental analysis instruments, contact SciSPX to speak with a specialist.

Frequently Asked Questions

How often should I replace the GC separation column in my CHNS analyzer under normal operating conditions?

Replacement frequency depends on sample throughput, matrix complexity, and the types of samples routinely analyzed. As a general guideline, labs running moderate volumes of clean organic matrices may get several hundred to over a thousand analyses from a single column, while labs processing halogenated, sulfur-rich, or high-ash samples will see significantly shorter service life. Rather than following a fixed calendar schedule, track retention time drift and peak resolution trends over time — these are the most reliable indicators that column replacement is approaching, regardless of run count.

Can poor peak separation affect the accuracy of my elemental percentages, even if the peaks still look somewhat resolved?

Yes — partial peak overlap is one of the most common sources of systematic error in CHNS analysis because it is easy to overlook on a routine chromatogram. When two peaks are not fully baseline-resolved, the integration software may attribute signal from one element to an adjacent peak, causing one element to be over-reported and another to be under-reported. Always validate resolution against a certified reference material with known elemental percentages, not just by visual inspection of peak shape, to catch this type of error before it affects your data.

What carrier gas purity grade should I be using, and does it really make a difference in practice?

For CHNS analyzers, helium or nitrogen carrier gas of at least 99.999% purity (5.0 grade) is typically required, and in practice the difference between grades is significant. Even trace levels of moisture or oxygen in the carrier gas will gradually oxidize the reduction tube packing, contaminate the separation column, and cause the very peak degradation issues described in this post. Always use gas from a reputable supplier, install an in-line moisture and oxygen trap on the carrier gas line, and replace those traps on a scheduled basis as part of your preventive maintenance routine.

Is it possible for a single contaminated or unusual sample to permanently damage the separation column?

In most cases a single problematic sample will not cause permanent damage, but it can accelerate column degradation significantly — particularly if the sample contains high concentrations of halogens, heavy metals, or inorganic salts that deposit on the column packing. If you suspect a sample has caused acute contamination, run a conditioning cycle immediately afterward and then check resolution with a certified reference material before continuing sample analysis. If separation does not recover after conditioning, early column replacement is more cost-effective than continuing to run samples and risk compromising your data.

How do I know whether my reduction tube is the problem if I don't have a spare to swap in for comparison?

Without a spare tube for direct comparison, the most useful diagnostic approach is to cross-reference your current chromatogram against a baseline chromatogram run on the same certified reference material when the reagents were known to be fresh. Ghost peaks appearing between the main elemental signals, or unusual baseline elevation around the nitrogen region, are strong indicators of reduction tube exhaustion even without a direct swap test. Also check your run log — if you have processed a high number of halogenated samples since the last reagent change, exhaustion is a likely contributor regardless of what the chromatogram looks like.

What documentation should I keep to make CHNS troubleshooting faster and more systematic over time?

At a minimum, maintain a log that records the date, run number, carrier gas lot, and a reference chromatogram for every consumable change — column, reduction tube, halogen scrubber, and combustion tube liner. Storing overlay chromatograms from certified reference material runs at regular intervals gives you a visual history of how resolution and retention times evolve between maintenance events. This kind of documentation not only speeds up root cause identification during troubleshooting but is also essential for demonstrating instrument control in GMP- or GLP-regulated environments.

Are there any preventive measures I can take to extend the service life of the separation column and reagent tubes?

Several practical habits can meaningfully extend consumable life: always run a blank or conditioning sample before and after unusually complex matrices, avoid overloading the system by keeping sample weights within the recommended range for your instrument model, and purge the system with carrier gas after any extended downtime to clear residual moisture. Additionally, scheduling regular preventive maintenance — rather than waiting for performance to degrade — allows you to replace consumables at the end of their useful life rather than after they have already compromised your data quality.

Related Articles

This content was generated with the help of AI and it may contain mistakes

Contact our Xperts

Prefer to give us a call?

The Netherlands
+31 (0)294 280 450

Belgium & Luxembourg
+32 (02)2 334 22 70